ATmega128
Errata
The revision letter in this section refers to the revision of the ATmega128 device.
ATmega128 Rev. F to M
?
?
?
?
?
?
First Analog Comparator conversion may be delayed
Interrupts may be lost when writing the timer registers in the asynchronous timer
Stabilizing time needed when changing XDIV Register
Stabilizing time needed when changing OSCCAL Register
IDCODE masks data from TDI input
Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request
1. First Analog Comparator conversion may be delayed
If the device is powered by a slow rising V CC , the first Analog Comparator conversion will
take longer than expected on some devices.
Problem Fix/Workaround
W hen the device has been powered or reset, disable then enable theAnalog Comparator
before the first conversion.
2. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
3. Stabilizing time needed when changing XDIV Register
After increasing the source clock frequency more than 2% with settings in the XDIV register,
the device may execute some of the subsequent instructions incorrectly.
Problem Fix / Workaround
The NOP instruction will always be executed correctly also right after a frequency change.
Thus, the next 8 instructions after the change should be NOP instructions. To ensure this,
follow this procedure:
1.Clear the I bit in the SREG Register.
2.Set the new pre-scaling factor in XDIV register.
3.Execute 8 NOP instructions
4.Set the I bit in SREG
This will ensure that all subsequent instructions will execute correctly.
Assembly Code Example:
CLI
; clear global interrupt enable
OUT
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
XDIV, temp
; set new prescale value
; no operation
; no operation
; no operation
; no operation
; no operation
; no operation
; no operation
; no operation
371
2467X–AVR–06/11
相关PDF资料
ATMEGA64RZAPV-10AU BUNDLE ATMEGA644P/AT86RF230 TQFP
ATP101-TL-H MOSFET P-CH 30V 25A ATPAK
ATP102-TL-H MOSFET P-CH 30V 40A ATPAK
ATP103-TL-H MOSFET P-CH 30V 55A ATPAK
ATP104-TL-H MOSFET P-CH 30V 75A ATPAK
ATP106-TL-H MOSFET P-CH 40V 30A ATPAK
ATP107-TL-H MOSFET P-CH 40V 50A ATPAK
ATP108-TL-H MOSFET P-CH 40V 70A ATPAK
相关代理商/技术参数
ATMEGA128RFA1-ZUR SL514 制造商:Atmel Corporation 功能描述:
ATMEGA128RFA1-ZUR00 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC REVF 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC REVF T&R - Bulk 制造商:Atmel from Components Direct 功能描述:ATMEL ATMEGA128RFA1-ZUR00 MICROCONTROLLERS (MCU) 制造商:Atmel 功能描述:Atmel ATMEGA128RFA1-ZUR00 Microcontrollers (MCU) 制造商:Atmel Corporation 功能描述:MCU AVR 2.4GHZ 128K FLASH 64VQFN 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC Revision F 制造商:Atmel 功能描述:2.4GHZ 802.15.4 128K SOC REVF
ATMEGA128RFR2-ZF 功能描述:IC RF TXRX+MCU 802.15.4 64-VFQFN 制造商:microchip technology 系列:- 包装:托盘 零件状态:在售 类型:TxRx + MCU 射频系列/标准:802.15.4 协议:Zigbee? 调制:DSSS, O-QPSK 频率:2.4GHz 数据速率(最大值):2Mbps 功率 - 输出:3.5dBm 灵敏度:-100dBm 存储容量:128kB 闪存,4kB EEPROM,16kB SRAM 串行接口:I2C,JTAG,SPI,USART GPIO:35 电压 - 电源:1.8 V ~ 3.6 V 电流 - 接收:5mA ~ 12.5mA 电流 - 传输:8mA ~ 14.5mA 工作温度:-40°C ~ 125°C 封装/外壳:64-VFQFN 裸露焊盘 标准包装:260
ATMEGA128RFR2-ZU 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC IND 85C - Bulk
ATMEGA128RFR2-ZUR 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC 85C T&R - Tape and Reel
ATMEGA128RZAV-8AU 功能描述:射频微控制器 - MCU AVR Z-Link Bundle RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube
ATMEGA128RZAV-8MU 功能描述:射频微控制器 - MCU AVR Z-Link Bundle RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube